China Emergency Light Manufacturers – Emergency Exit Sign: Detailed Installation Procedures
Installing an exit sign or emergency light can be relatively straightforward, especially if you have experience or basic tool knowledge to hang or install other objects. Most lights or signs are accompanied by instructions. If they don’t, most manufacturers will have a customer service number that you can call to get help for a particular model.

  Before an emergency installation

  When installing an emergency light, be sure to consult an electrician if you are not familiar with the correct safety procedures. The emergency light will be connected to the wires of the building or home to be able to sense when the power is off. Even in the event of a power outage or tripping of the circuit breaker, the unit signals and has a 90-minute backup power source to illuminate the path to the exit.

  Of course, it is very important to connect the emergency light circuit breaker before installing the emergency light to avoid electric shock and electric shock. Before disabling the power supply, check that all spare batteries in the device are properly installed. This command will guide you through the proper power supply when the power is turned off.

  Each unit contains instructions for the model provided. Before performing any installation procedures, make sure that the circuit where the emergency light is to be installed is turned off.

  Your electrical system requires 2 or 3 connections to properly install the emergency light. Improper installation of the emergency light can damage the transformer and the board, rendering the unit inoperable and damaged.

  First, determine the voltage at which the connection to the emergency luminaire is 120 or 277 volts. Next, check the connections on the device and there will be 3 or 4 wires to be colored and marked as:

  120v line (black)

  277v line (red)

  Ordinary wire (white)

  Ground wire (green – not included in all models)

  Connect the correct voltage and common wires to the electrical conduit. If your emergency luminaire requires it, please connect the ground wire. Do not connect 120V and 277V wires – the unit will malfunction.

  Turn on the circuit, charge the emergency light and its backup battery for 24 hours, then back up the battery for 90 minutes.

  Emergency lighting installation program

  If your wall is not connected to a fixture, you will need to consult an electrician to make the necessary wiring. Depending on the device, it is usually installed or partially installed before the wiring is connected. Wiring uses 120 or 277v AC power. This allows the battery to be charged on the building’s power supply and then directly into the battery if the building’s power is stopped.

  Most emergency lights are mounted using mounting brackets, while other emergency lights have prefabricated areas for securing the screws to the wall studs through the back. Be sure to familiarize yourself with your specific model and its installation instructions. Usually when screws, screws and brackets are used, these and wiring will be covered by a metal or thermoplastic casing.

  Exit flag installer

  Many of the considerations for installing emergency lights work when installing the exit sign. It must be determined whether the sign is connected to the building’s power source or the standby generator, or only to the building’s power source. Depending on the design, some exit signs will have a side mounting bracket that leads to the hanging light. Other signs will be screwed into the stud through the back of the sign and the panel will slide forward to cover the bulb and casing. As with emergency lights, an electrician is required if the area is not connected.

  Make sure that the power is turned off before installing the exit sign. The electrical LED exit sign is installed using a 120 or 277v power supply and is equipped with a backup battery system similar to an emergency light. The exit sign uses a nickel-cadmium (NiCad) emergency light battery that is smaller than the lead-acid battery in the emergency light.

  Perhaps the easiest sign to install is the self-illuminating exit sign, powered by 氚. The self-illuminating 氚 exit sign does not need to be connected to the building’s power source or generator because it is self-illuminating. Simply follow the instructions to attach the logo to the wall studs. For specific installation questions about your model, please consult the manufacturer of your particular fixture or logo.

  It is important to have a plan for the most efficient placement and use of emergency lights before the installation is complete. For any facility owner or manager, emergency lighting is not cheap, you are not only responsible for the cost-effectiveness of the building, but must also operate in accordance with all government regulations.

  Depending on the number of emergency lighting requirements placed in the process, the law insists that emergency lights be installed in all areas where personnel may be found, and that all exit routes (exit routes/routes) (sidewalks and streets) or safety assembly areas are installed from the building to the public area. This essentially means that the following areas need to be lit:

  All work areas

  All offices, vestibules and waiting areas

  All corridors

  All sales areas

  All external walkways lead to public roads

  Minimum lighting requirements

  OSHA regulations and regulations stipulate that the entire exit route should illuminate at least one candle force measurement 1 foot above the ground. This must always be considered before installing any emergency lighting. The space between the illumination models depends on the amount of light (in lumens) provided by that particular illumination unit. As long as the actual light produced depends on the wattage, voltage and efficiency of the bulb, we are unable to provide an accurate distance for the luminaire, as each application requires a different solution.

  Emergency lighting requirements

  In the event of an emergency or complete power outage in a building, emergency lighting is required to illuminate each area of ​​the building where visitors or people are located. This intrinsically means that all corridors for all exits must also be illuminated with the exit gate itself. In addition, the sidewalks outside the facilities from those exit points to public roads (sidewalks, streets) or safely assembled areas must be lit.

  The China Emergency Light Manufacturers stated that any place where people are expected to need emergency lighting may result in a large number of emergency lights. Although offices designed for individual occupants may not require emergency lighting, they must have the corridors outside the office properly lit.

https://www.linsheng.com